close
Categories
Filter By
Company
Accuracy
- 0.01% FS 4
- 0.1%__±0.1 mm 7
- 0.1 mm 2
- 0.02% FS 2
- 0.2%__±1 mm/s 6
- 0.2%__±2.5 mm/s 1
- 0.2% FS 1
- 0.3% FS 1
- 0.3...0.1 1
- 0.04%__0.065% 1
- 0.4 %__± 1 mm/s 1
- 0.5% FS 2
- 0.6%__1% 1
- 0.10% 1
- 0.15% 1
- 0.025%__0.1% 1
- 0.25% 4
- 0.30% 1
- 0.50% 22
- 2.3% FS 1
- 2.5 1
- 3...24 mm 2
- 4% 1
- ±0.2 l/min 1
- ± 0.3%__± 1.5% 2
- ±0.4 l/min 3
- ± 0.5% FS 3
- ± 0.5% FS__± 1% FS 1
- ±0.5% of flow rate 1
- ±0.10 % 1
- ±0.10 %__±0.20 % 1
- ±1% 3
- ±1 % of range, ±3 % of reading (from 15 l/min) 1
- ±1.5mm 1
- ±1.25 mm 1
- ± 1__± 3% 1
- ± 2%__± 2°C 4
- ± 2°C 1
- ±2mm 4
- ±3°C 1
- ± 3 mm 2
- ± 5% 5
- EN1434 Class 3, typical ±(0.5 + 3K/ΔΘ) [%] 1
Medium Temperature
Pressure Range
3...24 mm, 0.3...0.1 - ± 3 mm
5 items
RLS-1000 Float Switch
8111
The WIKA RLS-1000 float switch is a robust, reliable and inexpensive float switch. The monitoring of levels, as well as dry-run protection and overflow protection, are cost-sensitive applications in the machine-building industry, therefore a float switch is a perfect solution for many plants. The RLS-1000 float switch offers reliable measurements for the level in vessels with water, oil, diesel or other liquids by means of a permanent magnet and frictionless reed contacts at max. 4 defined switch points and can be used in a medium temperature range from -30 to +150 °C (-22 to +302 °F). The WIKA RLS-1000 float switch is simple, easy to use and fast to integrate because it does not need to be calibrated or set during the installation. This greatly improves the ease of handling, especially in confined installation situations. Also, since its robust design makes it resistant to vibrations and shocks, maintenance costs are minimal.
- USD
RLS-2000 Float Switch
8114
The WIKA RLS-2000 float switch is a reliable and inexpensive float switch made of high-quality plastic. The WIKA RLS-2000 float switch is particularly suited for measuring the levels of aggressive and corrosive media, such as bases and acids. For cost-sensitive applications such as the monitoring of levels or overflow and dry-run protection, float switches are an ideal solution. The WIKA RLS-2000 float switch detects the level using a permanent magnet and frictionless reed contacts at up to 4 defined switch points, without contact and thus free from wear. Integration as a limit level switch is simple, convenient and fast, because no adaptation or calibration is required during installation. The robust design minimises service and maintenance costs.
- USD
RLT-1000/2000 Reed-chain Level Sensor
8194
The WIKA RLT-1000 Reed-chain level sensor has been developed for measuring the levels of liquids. The stainless steel used is suitable for a multitude of media, such as, for example, oil, water, diesel and refrigerants. A permanent magnet built into the float triggers, with its magnetic field, the resistance measuring chain built into the guide tube. The entire assembly corresponds to a 3-wire potentiometer circuit. The measured resistance signal is proportional to the level. The WIKA RLT-1000 is optionally available with a 4 … 20 mA analogue output.
- USD
RLT-3000 Reed-chain Level Sensor
8200
The WIKA RLT-3000 level sensor with temperature output combines the recording of the level and temperature of liquids in a single measuring point. The stainless steel used is suitable for a multitude of media, such as, for example, oil, water, diesel and refrigerants. A permanent magnet built into the float triggers, with its magnetic field, the resistance measuring chain built into the guide tube. The built-in transmitter converts the signal of the resistance measuring chain into a 4 … 20 mA current signal. The current signal is proportional to the level. For the temperature measurement, there is a platinum measuring resistor built into the end of the guide tube.
- USD
CPC2000 Portable Low-Pressure Controller
8212
The WIKA CPC2000 portable low pressure controller is used in the areas of heating, ventilation, air conditioning, filtration, clean room, and medical technology as a calibrator or as highly-accurate measurement equipment and/or precise pressure transducer. The WIKA CPC2000 low-pressure controller is a mains or battery-operated pressure controller with internal, automatic pressure generation and pressure reference. The pressure generation is achieved using an integrated, electric pump, which makes a positive and/or negative pressure available on both the tube connections. As soon as the instrument is switched on, a zero-point adjustment is automatically carried out, so that a zero-point drift is eliminated. The subsequent preparation of a calibration requires only a few settings. First, using the MENU button, select one of the stored pressure units and the variable pressure change step in the range of 0 … 50 %. Then, once the full scale has been entered in Control Mode, the pressure can be easily increased or decreased by the defined level using the navigation buttons. To check whether the calibration assembly or the test item has a leak, the LEAK button can be used. With this, the pressure is locked into the test assembly and any pressure drop there might be, as well as the the time this takes, is measured and displayed. The CPC2000 has an RS-232 and USB interface, enabling communication and data exchange with a PC. WIKA-Cal calibration software is available for the CPC2000. WIKA-Cal also offers, over and above PC-supported calibration, the management of the calibration and instrument data in an SQL database. The accuracy of the instrument is certified by a factory calibration certificate.
- USD
1 - 5 of 5
1